Rapberry PI Wifi Router - Revision history

Vincent: static ip

2016-12-29T09:30:30Z

static ip

← Older revision		Revision as of 09:30, 29 December 2016
Line 161:		Line 161:

	</syntaxhighlight>		</syntaxhighlight>

			=== Static IP Address ===
			<syntaxhighlight lang="console">
			# Always give the host with Ethernet address 11:22:33:44:55:66
			# the name fred and IP address 192.168.0.60 and lease time 45 minutes
			dhcp-host=11:22:33:44:55:66,fred,10.18.16.14,45m

			</syntaxhighlight>To find the mac address look at file <code>/var/lib/misc/dnsmasq.leases</code>

	== Configure IP Routing ==		== Configure IP Routing ==
	{{WIP}}		{{WIP}}

Vincent: dnsmasq config

2016-12-23T18:46:54Z

dnsmasq config

@@ Line 6: / Line 6: @@
 == Install ==
 <syntaxhighlight lang="console">
-$ sudo apt install hostapd
+$ sudo apt install hostapd dnsmasq
 </syntaxhighlight>
@@ Line 131: / Line 131: @@
 == Configure DHCP ==
 {{WIP}}
 == Configure IP Routing ==
 {{WIP}}

Vincent: Access point

2016-12-23T15:00:24Z

Access point

@@ Line 14: / Line 14: @@
 dhcpcd is the default [https://en.wikipedia.org/wiki/Dynamic_Host_Configuration_Protocol DHCP] client in Raspbian. You need to disable it for the <code>wlan0</code> interface to avoid conflicts with the rest of the setup.
-Edit file <code>/etc/dhcpcd.conf</code> an add the following line at the end<syntaxhighlight lang="text">
+Edit file <code>/etc/dhcpcd.conf</code> an add the following line at the end<syntaxhighlight lang="nginx">
 denyinterfaces wlan0
 </syntaxhighlight>{{Warning|msg=}}This must be above any <code>interface</code> lines you may have added
@@ Line 25: / Line 25: @@
 The second step is to configure the interface with a static IP address.
-Edit the file <code>/etc/network/interfaces</code> and replace the block related to <code>wlan0</code> by<syntaxhighlight lang="text">
+Edit the file <code>/etc/network/interfaces</code> and replace the block related to <code>wlan0</code> by<syntaxhighlight lang="ini">
 allow-hotplug wlan0
 iface wlan0 inet static
@@ Line 40: / Line 40: @@
 == Configure Access Point ==
 {{WIP}}
 == Configure DHCP ==

Vincent: Created page with "== Prerequisite == For this guide, you will need * A '''Raspberry Pi 3''': It can work on previous generations but you will need a WiFi USB card plus eventually manually insta..."

2016-12-23T13:16:48Z

Created page with "== Prerequisite == For this guide, you will need * A '''Raspberry Pi 3''': It can work on previous generations but you will need a WiFi USB card plus eventually manually insta..."

New page

== Prerequisite ==
For this guide, you will need
* A '''Raspberry Pi 3''': It can work on previous generations but you will need a WiFi USB card plus eventually manually install drivers.
* '''Raspbian''': This guide is written for Raspbian.

== Install ==
<syntaxhighlight lang="console">
$ sudo apt install hostapd
</syntaxhighlight>

== Configure Interface ==

=== dhcpcd ===
dhcpcd is the default [https://en.wikipedia.org/wiki/Dynamic_Host_Configuration_Protocol DHCP] client in Raspbian. You need to disable it for the <code>wlan0</code> interface to avoid conflicts with the rest of the setup.

Edit file <code>/etc/dhcpcd.conf</code> an add the following line at the end<syntaxhighlight lang="text">
denyinterfaces wlan0
</syntaxhighlight>{{Warning|msg=}}This must be above any <code>interface</code> lines you may have added

And restart <code>dhcpcd</code> using<syntaxhighlight lang="console">
$ sudo systemctl restart dhcpcd.service
</syntaxhighlight>

=== Interface ===
The second step is to configure the interface with a static IP address.

Edit the file <code>/etc/network/interfaces</code> and replace the block related to <code>wlan0</code> by<syntaxhighlight lang="text">
allow-hotplug wlan0
iface wlan0 inet static
address 10.18.16.1
netmask 255.255.255.0
network 10.18.16.0
broadcast 10.18.16.255
# wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
</syntaxhighlight>And apply the configuration using<syntaxhighlight lang="console">
$ sudo ifdown wlan0
$ sudo ifup wlan0
</syntaxhighlight>

== Configure Access Point ==
{{WIP}}

== Configure DHCP ==
{{WIP}}

== Configure IP Routing ==
{{WIP}}